- Elsawin 3.9 setup vloses disappears how to#
- Elsawin 3.9 setup vloses disappears manuals#
- Elsawin 3.9 setup vloses disappears code#
Power Steering Pressure Switch (PSPS) circuit is open 2. = 45 Injected Coil 1 primary circuit failure = 45 Injected Coil 2 primary circuit failure = 48 Injected Coil 3 primary circuit failure = 49 Injected Spark Output (SPOUT) signal defaulted to 10 degrees BTDC / SPOUT circuit open = 51 Injected Engine Coolant Temperature sensor (CTS) indicate -40☏ / circuit open = 52 Injected 1. = 42 Injected Heated Oxygen Sensor (HO2S) circuit indicates system rich (right HO2S). 2.No Heated Oxygen Sensor (HO2S) switching detected rear HO2S). Heated Oxygen Sensor (HO2S) circuit indicates system lean (rear HO2S). Exhaust back pressure high / Pressure Feedfback (PFE) circuit voltage high = 35 Injected Pressure Feedfback (PFE) circuit above maximum voltage = 41 Injected 1. Pressure Feedfback (PFE) sensor voltage out of range 2. = 33 Injected Exhaust Gas Recirculation (EGR) valve opening not detected = 34 Injected 1. SPARK OUTPUT (SPOUT) circuit open 2.Ignition Diagnostic Monitor (IDM) circuit failure SPOUT circuit grounded = 19 Injected CID circuit failed = 21 Injected Engine Coolant Temperature (ECT) sensor out of Self-Test range = 22 Injected Back Pressure (BP) sensor out of Self-Test range = 23 Injected Throttle Position sensor (TPS) out of Self-Test range = 24 Injected Air Charge Temperature sensor (IAT) out of Self-Test range = 25 Injected Knock Ssensor not sensed during Dynamic Response Test = 26 Injected Mass Air Flow sensor (MAF) out of Self-Test range = 29 Injected Insufficient input from Vehicle Speed Sensor (VSS) = 31 Injected Pressure Feedfback (PFE) circuit below minimum voltage = 32 Injected Pressure Feedfback (PFE) circuit voltage low. Electronic Engine Control (EEC / PCM) processor Keep Alive Memory (KAM) test failed = 18 Injected 1. Electronic Engine Control (EEC / PCM) processor ROM test failure 2.
Elsawin 3.9 setup vloses disappears code#
Centech Digital Multimeter automotive multimeter measures volts, amps, ohms, frequency, temperatures SmartSpec Diagnostic Specifications Cd complete obd diagnostic specifications for Ford 1990-2003 Code Fuel Delivery Type Description = 11 Injected System Pass = 12 Injected Unable to control RPM during Self-Test high RPM check = 13 Injected Unable to control RPM during Self-Test low RPM check = 14 Injected Profile Ignition Pickup (PIP) circuit failure = 15 Injected 1.
Elsawin 3.9 setup vloses disappears manuals#
This is not meant to be a substitute for information in the factory service manuals or the product service training manuals. OBD diagnostic does not have to be difficult or inconclusive. This information combined with proper testing procedures, specifications, and tools like a digital multimeter can help you fix the vehicle right the first time. When possible we give the more descriptive name of the component and the more commonly known OBD II component name. The codes are defined as to what system is affected.
![elsawin 3.9 setup vloses disappears elsawin 3.9 setup vloses disappears](http://blog.obdii365.com/wp-content/uploads/2017/09/install-elsawin-5.2-on-windows-8-10-4.jpg)
The codes are listed seperately based upon fuel delivery type.
![elsawin 3.9 setup vloses disappears elsawin 3.9 setup vloses disappears](http://blog.obdii365.com/wp-content/uploads/2017/09/install-elsawin-5.2-on-windows-8-10-16.jpg)
Elsawin 3.9 setup vloses disappears how to#
This page explains how to get the codes without any special tools.